2004 Ford Cab & Chassis
Mileage
148,466
Service Date
1/23/2026
Services Performed
- REPLACE BROKEN CLAMP AND REALIGN PIPE TO TURBO
- REPLACE COOLANT BOTTLE DUE TO IT LEAKING FROM BEING MELTED
Shane S. gave our service a 5 star review on 1/23/2026
-
-
2016 Chevrolet Silverado 2500 HD
Mileage98,011Service Date12/16/2025Services Performed- tested glow plug harness tested good test glow plug it was out of spec
- remove fender liner to remove glow plug lube one new glow plug install reinstall fender liner tested no light at this time
Jim A. gave our service a 5 star review on 12/17/2025 -
2019 Ford F-350 Super Duty
Mileage141,603Service Date11/21/2025Services Performed- VIBRSTION COM ING FROM FRONT HUBD BEING LOCKED HORN WORKS WITH NO ISSUES
- UNBOLTED OLD TIE ROD AND COUNTED THREADS AND REPLACED WITH NEW TIE ROD AND AND RETIGHTEND EVERYTHING TO SPEC
- REMOVED HUB AND KNUCKLE AND AXLE SHAFT PRESSED OUT OLD BLOWN OUT BALL JOINTS AND REPLACED WITH NEW BALL JOINTS AND REGRESSED AND RE INSTALLED KNUCKLE AND HUB ASSEMBLY
- Replace front brake pads and rotors. Clean and lubricate brake calipers and slide mechanisms. Check and fill brake fluid. Bleed air from system. Road test vehicle.
- Replace rear brake linings. Inspect condition and thickness of rear brake disc rotors. Retract rear brake caliper actuators. Clean and lubricate rear brake caliper slide mechanism. Adjust parking brake. Road test vehicle.
- REMOVED 4 BOLTS AND TUBE FROM THE BREATHER AND REMOVED AND REPLACED WITH NEW CCV AND RETIGHTEND TO SPEC
- Perform LOF With BG Diesel Oil Conditioner, Replace Fuel Filters & Install BG Diesel Fuel System Cleaner, Replace Air filter, Top Off Fluids, Rotate Tires & Set Pressures, Inspect Front & Rear Brakes, Steering & Suspension, Grease All Zerk Fittings, Perform Multi-Point Inspection.
Ricardo F. gave our service a 5 star review on 11/21/2025 -
2017 Ford F-350 Super Duty
Mileage207,337Service Date11/8/2025Services Performed- removed transmission to access upper oil pan. during removal of transfer case skid plate all 4 bolts spun inside the frame. extraction is required. removed upper oil pan and cleaned off engine block. installed older gasket style upper oil pan and new lower oil pan. let sealant cure over night before oil was put into truck. re installed transmission. added engine oil and took vehicle for multiple road test. no leaks from oil pans at this time.
- R&R CCV filter
- Cut all seized bolts & remove threaded clip retainers. Grind areas / holes on frame which bolts are fastened to, weld in flange nuts. Install new flange bolts with antiseize to prevent future concerns.
Jay W. gave our service a 5 star review on 11/10/2025 -
2011 Ford Cab & Chassis
Mileage113,659Service Date10/9/2025Services Performed- R&R both exhaust manifolds
- found 2 bolts to be broken on the drives side. extracted both bolts and replaced all hardware
- verified concern. found back up alarm to be wired improperly. cut one wire to the back up alarm. found 2 cab lights to be out.
- Perfomed MPI, thoroughly looked over vehicle and provided customer with any recommendations.
- Replace drivers outer tie rod end.
- Road test vehicle. Check all suspension and steering parts for wear. Check tire pressure and condition. Check riding height. Check alignment of all four wheels. Adjust caster, camber, toe-in, and thrust angle as needed on all four wheels. Center ste
- R&R customer supplied washer fluid pump
- R&R 2 cab light bulbs
- R&R rotted power steering line
Andrew R. gave our service a 5 star review on 10/9/2025 -
2013 Jeep Wrangler
Mileage88,314Service Date9/20/2025Services Performed- verified concern. found fans to not be turning on. referred to wiring diagrams. verified fan operation via commands with scan tool. suspect TIPM assembly.
- Perform BG cooling system flush, add cooling system cleaner, power flush with machine & new coolant. Add cooling system conditioner.
- R&R TIPM assembly. fans work as they should
Fernando R. gave our service a 5 star review on 9/23/2025 -
2012 Ford Pickup
Mileage500,913Service Date8/15/2025Services Performed- Performed LOF, greased front end and topped off vital fluids to vehicle. No further action needed at this time.
Jaime M. gave our service a 5 star review on 8/16/2025 -
2019 Chevrolet Silverado 2500 HD
Mileage97,185Service Date8/12/2025Services Performed- Verify & inspect / self test codes: P0205 (injector #5 circuit), P0300 (engine misfire). R&R bank 1 CAC pipe & injector cover, visually inspect harness & connector. Found connector signs of heat / poor terminal pin fit. Matches TSB# 23-NA-027 for codes, concern & connector condition.
- Soldier & heat shrink new service connector pigtails for cyl's# 1 & 5 fuel injectors, clean & apply dielectric grease to all connectors on bank 1. Clear codes & retest / road test & monitor misfire counter, all ok. Customer returned with same concern, P0205 (injector #5) code back. Check injector resistance, within spec. Check new connector, harness etc ok. Refer to wiring schematic for any shared components on circuits, R&R right side bank injector cover & disconnect each injector while monitoring injector #5 status, injector #5 status changed to ok when injector #2 disconnected. Found same concern on injector #2 connector. Replace faulty connector & clean / dielectric grease all connectors. Clear code & retest / road test & monitor misfire & injector status, all ok.
David H. gave our service a 5 star review on 8/12/2025 -
2006 Ford Pickup
Mileage134,214Service Date7/30/2025Services Performed- Self test codes: pass. Oil level & condition ok (slightly low). Low side oil pressure slow to build, PID monitor ICP / IPR / FICM. ICP slow to build & IPR 85%. Leak present. Air test h.pres system, pass. Recent stand pipes, dummy plugs & IPR. Suspect h.pres pump. Able to start with silicone spray, would remain running until oil temp rose above 140 degrees and IPR increased. Recommend replacement of h.pres pump & retest.
- R&R engine oil filter
- removed intake and turbo to access high pressure oil pump. turbo had no endplay. during removal of the intake, notices both belts to be cracked. replaced both belts with heavy duty ones. R&R high pressure oil pump and primed system. re installed turbo and intake.
- removed intake to access oil cooler. R&R oil cooler and replaced all seals. re installed intake
- installed coolant filter kit
Scott R. gave our service a 5 star review on 7/30/2025 -
2012 RAM Pickup
Mileage169,967Service Date7/17/2025Services Performed- Evac / vacuum & charge system, leak present at condensor. After condensor replacement, a/c inop & pressures erratic / variations from 115 psi to 0 psi. Further inspection with scope found evaporator core faulty / clogged.
- Replace a/c compressor, tensioner & belt.
- Replace a/c accumulator / drier.
- A/C PERFORMANCE – Testing – [Includes: Gauge check, leak test and partial charge.]
- Replace a/c condensor.
- Replace expansion valve.
Ryan V. gave our service a 5 star review on 7/18/2025
